Fletcher Custom Pistols, LLC Custom work on 1911 pistols, Browning Hi-Powers and Smith & Wesson revolvers
SMITH & WESSON REVOLVER SERVICES

Services are offered on what I believe to be one of the finest double action revolvers made - Smith & Wesson.
Services available include accurizing and action/trigger work for purposes from carry/defense to competition.
Revolver Action Work

Action work prices are for labor only and do not include parts that may be required such as springs, shims, etc.

Deluxe Action Work (S&W K, L, N frames)                                                                                                  $125.00
Action tuned for smoother and lighter trigger pull.
Includes:  align yoke, center pin and ejector rod; set cylinder end shake; smooth
cylinder rotation; set cylinder headspace; check barrel/cylinder gap; check timing
(additional cost if correction needed); polish action contact surfaces; set spring
tensions.

Carry Action Work (S&W J-frame)                                                                                                               $110.00
Action tuned for a smoother and slightly lighter (to maintain reliabililty) trigger pull.
Includes:  set cylinder end shake; smooth cylinder rotation; set cylinder headspace;
check barrel/cylinder gap; check timing (additional cost if correction needed); polish
action contact surfaces; set spring tensions.

Competition Action/Accurizing Work (S&W K, L, N frames) - The Ultimate Revolver                                    $325.00
A competition action and accurizing job combining techniques learned from master
pistolsmiths Jack Weigand and Ron Power (and a few tricks of our own!).
Includes:  All items listed in the Deluxe Action Work plus additional detailing of every action
component for a silky smooth action; competition pull weight spring settings; forcing cone recut;
barrel recrowned; trigger rounded and polished; internal trigger overtravel stop; yoke ball
detent; cylinder chambers chamferred; number stamped chambers (when practical).
Barrel set back at additional cost if required.

Round and Polish Trigger Face                                                                                                                         $30.00
Install Internal Overtravel Stop                                                                                                                          $25.00
Remove Hammer Spur and Convert to Double Action Only                                                                              $85.00
Detail Strip, Clean, Lube and Inspect                                                                                                                $55.00


Revolver Cylinder Work

Correct Cylinder End Shake (may require barrel set back which is not included)                                                $45.00
Straighten and Align Yoke                                                                                                                                $25.00
Straighten and Align Ejector Rod                                                                                                                      $35.00
Retime Cylinder                                                                                                                                                $45.00
Install Oversize Cylinder Stop                                                                                                                           $45.00
Install Ball Detent in Yoke (includes parts)                                                                                                        $55.00
Chamfer Cylinder Chambers                                                                                                                             $35.00
Ream Undersized Cylinder Throats                                                                                                                   $45.00
Number Stamp Revolver Chambers                                                                                                                  $35.00


Revolver Barrel Work

Shorten Barrel and Modify for Weigand Interchangable Front Sight System                                                     $175.00
     (only performed on heavy walled barrels with raised sight ribs)
Set Barrel Back to Correct Excessive Barrel/Cylinder Gap; Recut Forcing Cone                                             $100.00Correct Insufficient Barrel/Cylinder Gap; Recut Forcing Cone                                                                           $35.00
Recut Forcing Cone                                                                                                                                         $30.00
Recrown Barrel Muzzle                                                                                                                                    $40.00


Revolver Sight Work


Install Weigand Interchangeable Front Sight System (dependent on part availability)                                         *$75.00
Install Pin-On Style Front Sight Blade                                                                                                               $30.00
Test fire and zero sights to point of aim at 15 yards with FMJRN commercial ammunition                                  $45.00


Revolver Metal Work

Convert Square Butt to Round Butt (smooth strap only)                                                                              **$105.00
     (customer must provide grips)
Dehorn Entire Revolver for Carry                                                                                                                 **$65.00


*  Minor refinishing will be cold blued.               ** Complete refinishing required.


All prices listed in the service schedules are labor only for work performed on your firearm and do not include parts or materials unless noted otherwise. All prices and specifications are subject to change.

 
Web site copyright © 2004 - 2017 Fletcher Custom Pistols, LLC
All Rights Reserved.